The author is making a number of good pointers regarding A Step-by-Step Guide to Installing a Bathtub as a whole in the article below.
Setting up a tub isn't exactly brain surgery, however it does call for strong plumbing, carpentry, and also occasionally, tiling skills. Replacing an old bath tub with a new one is additionally a reasonably difficult project. If the old bathtub is easily easily accessible, the task can relocate rapidly; if you have to open up a wall to remove the old tub and position the brand-new bathtub, the job is much harder. In either instance, the job is within a residence handyman's abilities, although you will need a helper to move out the old bathtub and also set in the brand-new one. Ensure you have actually certified yourself for the job and also fit trying it. Instead of employing a contractor to take over a halfway-completed job, it is far better to consider employing one prior to you start. Possibilities are you might require an expert plumber to make tube links.
This article will help you install a brand-new bath tub in your shower room if you have currently bought a brand-new tub and do not need to alter the setup of your previous water system pipes.
Your tools as well as product list should comprise the following:
Planning for the Installment
To start with, the supporting frame provided with the bathroom must be fitted (if required) according to the manufacturer's instructions. Next, fit the faucets or mixer to the bath tub. When suitable the tap block, it is very important to see to it that if the faucet includes a plastic washing machine, it is fitted between the bath and the faucets. On a plastic bath, it is additionally practical to fit a sustaining plate under the taps system to prevent pressure on the tub.
Fit the flexible tap ports to the bottom of the two faucets using 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet through the hole in the bath. Use the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. See to it you make use of every one of the supplied washers.
Link the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bathroom ought to now prepare to be suited its last position.
Removing Old Touches
If you require to replace old faucets with new ones as a part of your installation, then the first thing you should do is detach the water supply. After doing so, turn on the taps to drain any water continuing to be in the system. The procedure of getting rid of the existing faucets can be quite troublesome as a result of the restricted gain access to that is typically the case.
Use a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the faucets. Have a cloth ready for the remaining water that will come from the pipes. When the supply pipelines have been removed, use the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the single taps from transforming during this procedure. As soon as the faucets have actually been removed, the holes in the bath/basin will need to be cleaned of any kind of old sealing compound.
Before proceeding to fit the new taps, compare the pipe links on the old taps to the brand-new faucets. If the old taps are longer than the new faucets, after that a shank adapter is needed for the new faucets to fit.
Installing the Tub
Utilizing the two wooden boards under its feet, place the tub in the required position. The wooden boards are useful in equally spreading the weight of the bathtub over the area of the boards rather than concentrating all the weight onto four small factors.
The following objective is to make sure that the bathtub is leveled all round. This can be accomplished by examining the level and readjusting the feet on the bathtub till the spirit level checks out degree.
To install faucets, fit all-time low of the outermost versatile tap adapter to the suitable supply pipeline by making a compression sign up with; then do the exact same for the various other tap.
Turn on the water system and check all joints and new pipework for leakages and tighten them if needed. Load the bath tub as well as likewise inspect the overflow electrical outlet as well as the typical outlet for leaks.
Ultimately, deal with the bath paneling as explained in the producer's instruction manual. Tiling as well as securing around the bath tub ought to wait up until the tub has actually been used at least when as this will certainly resolve it into its last placement.
Suitable New Touches
If the tails of the new faucets are plastic, after that you will certainly need a plastic port to prevent damages to the thread. One end of the port fits on the plastic tail of the tap as well as the various other end supplies a link to the existent supply pipes.
If you need to fit a monobloc, after that you will certainly need decreasing couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, place the tap in the installing opening in the bath/basin guaranteeing that the washers remain in place between the tap and also the sink. Secure the tap in position with the maker supplied backnut. When the tap is firmly in position, the supply pipelines can be attached to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with typical tap connectors. The previous kind ought to be connected to the faucet finishes first, tightening up just by hand. The supply pipelines can later be connected to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the area where the bath fulfills the ceramic tile, it is required to secure the joins with a silicone rubber caulking. This is important as the installation can relocate sufficient to fracture a stiff seal, causing the water to penetrate the wall surface in between the bath and the tiling, causing problems with dampness as well as possible leakages to the ceiling below.
You can choose from a range of coloured sealants to blend in your fixtures and also installations. They are sold in tubes and cartridges, as well as are capable of securing gaps as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of drenched paper or soft rope. Bear in mind to constantly load the bathtub with water before securing, to enable the activity experienced when the tub remains in use. The sealant can crack fairly very early if you do not take into consideration this motion prior to sealing.
Alternatively, ceramic coving or quadrant tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also easily readily available on the marketplace. It is suggested to fit the floor tiles making use of water-resistant or waterproof glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I am very drawn to How to Install a Bathtub Yourself and I really hope you appreciated my blog entry. Sharing is good. One never knows, you may be doing someone a favor. I praise you for your time. Visit again soon.
Get A Free Estimate